







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Kitchen Remodeling: The Homestead Owner’s Guide
We install Cambria-compatible kitchen remodeling in Homestead, and the honest number for most full kitchens here runs $14,000 to $45,000, with quartz countertop work alone landing between $2,000 and $6,500. Cambria is quartz, not stone that arrived as a slab and got cut down. It’s engineered from roughly 90% ground quartz bound in resin, which is why it can carry a lifetime warranty against staining and why it can also fail in ways natural granite never does.
Owners usually find out something is wrong in one of two ways. A hairline crack appears at a sink cutout or an inside corner, thin as a thread, and they assume it’s dirt until they run a fingernail across it. Or an edge chips at the dishwasher, a seam opens by a few thousandths, and the whole run of counters starts looking older than it is. We’re Rowan Construction Group, an independent contractor and not affiliated with Cambria, and we’ve set enough of this material to know which failures are surface-level and which mean the counter has to come out.
Which Cambria Models This Applies To

Cambria doesn’t sell “models” the way a refrigerator does. The product line is identified by the design name – Brittanicca, Ella, Torquay, the whole catalog of slabs – and by the slab format and thickness the fabricator ordered. That distinction matters when you’re matching a replacement or an addition. Two counters from the same design name can differ if one was cut from a 2cm slab and the other from a 3cm, and the edge profile machined into each is different too.
Here’s where owners get it wrong. They find a design name on an old invoice and order to that name alone, without the slab dimensions or the edge detail. Cambria’s standard jumbo slab is a fixed footprint, but the actual counter in your Homestead kitchen was cut to a template, and a new piece needs the same template or a fresh one. The label you want is usually a fabricator sticker under the overhang or on the cabinet gable, showing the design name, the batch or lot, and the thickness. Look there before you call anyone. If the sticker is gone, we measure the counter edge-to-edge and check thickness with a caliper – 2cm reads near 20mm, 3cm near 30mm – and that tells us which replacement path is honest. On the OEM-vs-aftermarket question: Cambria is sold through authorized fabricators, so there isn’t a genuine “aftermarket Cambria.” What exists is a competing quartz in a close color. We carry Cambria and Caesarstone, and when a color is discontinued or a single slab is needed fast, a Caesarstone match is often the faster route. If you also want cabinet, sink, or fixture lines priced in the same quote, we source KraftMaid, Wellborn, Kohler, and Silestone as well.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cambria Kitchen Remodeling Is Failing
- Hairline cracks radiating from a cutout. Quartz is strong in compression but less forgiving of a point load or a void under the counter. A crack at the sink or cooktop cutout usually means the substrate wasn’t fully supported, not that the slab was defective.
- Chipped edges at the dishwasher or a high-traffic corner. Chips concentrate where an edge profile is thin and something hard hits it. Cambria can be repaired at a chip, but the fix depends on whether the color runs through the body.
- Seams that read as a dark line or catch a fingernail. A seam opening means the adhesive failed or the two cabinets it bridges moved. In Homestead’s humidity, cabinets swell and shift more than owners expect, and the seam is where you see it first.
- Dull or cloudy patches that won’t polish out. Quartz holds a factory finish. Aggressive cleaners or a scrubbing pad can dull the resin surface, and that’s a finish problem, not a stain – it doesn’t come back with polish.
- Counter flexing or a hollow sound when tapped. That’s a support failure underneath, often a settled cabinet or a missing shim. Left alone, flex becomes a crack, and a crack near a cutout is the failure that forces replacement.
Replacement Cost & What’s Included

Countertop installation in Homestead runs $2,000 to $6,500 installed, and that range swings on three things: the square footage, whether you’re keeping the existing cabinets, and the edge profile. A straight edge on a standard run sits at the low end. A waterfall island or a full-height backsplash pushes it up. The full kitchen – counters plus cabinets, backsplash, and island – runs the $14,000 to $45,000 lead range for this page, with backsplash installation at $800 to $2,500 and an island at $3,000 to $10,000.
What’s in the number: the slab or slabs, templating, fabrication, the edge profile, removal and disposal of the old top, and the install labor. What keeps the price from moving after we start is our written process. Under Clause 1 of The Haven Standard, the price is written before anyone starts, and no work proceeds on a change until the change order is signed. The install carries the 365-Day Done Right Promise – if it’s not done right, we make it right. Ask about it; the terms page is public.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. You can safely check the fabricator sticker under the overhang, measure thickness with a caliper, and tap along the counter to hear where it sounds hollow. That’s diagnosis, and it’s useful. What you shouldn’t do yourself is pull a counter to inspect the substrate, cut or drill quartz for a new sink, or try to close a seam with a hardware-store epoxy. Quartz dust from cutting is a silica hazard and needs wet-cutting and proper respiratory protection, and a seam reset with the wrong adhesive fails again within a season. A 3cm quartz slab is heavy enough that a two-person lift with the wrong technique cracks it at the cutout – and that crack is a replacement, not a repair. We’d rather tell you that plainly than sell you a job you don’t need. If the diagnosis points to a fix, call us at (844) 834-4248 and we’ll walk through it.
FAQs

How long does Cambria last in a Homestead kitchen? Cambria’s own warranty is a lifetime limited warranty against staining, and the material itself holds up to Florida humidity better than wood or laminate because it doesn’t absorb water. The realistic failure isn’t the slab – it’s the install underneath it. A well-supported counter with a sound substrate lasts decades; a poorly shimmed one cracks at a cutout in a few years.
Can a cracked or chipped Cambria counter be repaired instead of replaced? Sometimes, yes. A chip at an edge can often be filled and blended, and a seam can be reset if the cabinets underneath are stable. A crack that runs through a cutout or crosses the slab usually means replacement, because a repair there doesn’t restore the structural strength. We’ll tell you which one you have before anyone quotes a job – call (844) 834-4248 for a free estimate.
How long does a Cambria countertop swap take? Templating is one visit, fabrication takes roughly a week to two depending on the design and slab availability, and the install itself is typically a single day for a standard kitchen. The full kitchen remodel around it runs longer – into weeks – once cabinets and backsplash are in the scope.
How do you source the right Cambria slab? We go through authorized fabrication channels and match on design name, thickness, and the edge detail from your template, not the invoice name alone. If the design is discontinued, we price a close Caesarstone alternative in the same quote so you can compare. Call (844) 834-4248 for a free estimate and we’ll put the sourcing in writing.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.
Contact
If you’re in Homestead and you’ve got a Cambria counter that’s cracked, chipped, or just not sitting right, the fastest way to a straight answer is a call. We’ll measure, tell you what we found, and put a written price in front of you before any tool comes off the wall. Call (844) 834-4248 for a free estimate. We’ll also do a free second opinion on any written estimate you already have, line by line, no charge.












