







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Bathroom Remodeling: The Homestead Owner’s Guide
We install Delta-compatible bathroom remodeling in Homestead, and a full bathroom remodel in this market typically runs $9,000 – $28,000 with a written flat price before any work begins. Delta trim and valve parts are matched to the exact series on your fixture, not guessed at the counter. Owners usually find us the way you probably did: a shower that won’t hold temperature, a cartridge that weeps behind the handle, or a tub spout pulling away from the wall with the set screw stripped. By the time the drip shows on the ceiling below, the failure has been running for weeks. We quote the repair and the surrounding remodel together so you see the whole number, not just the part.
Which Delta Models This Applies To
Delta’s residential line splits into a few families you’ll actually run into in Homestead homes built from the 1980s forward: the Monitor and Classic single-handle valve bodies, the MultiChoice universal rough-in, and the newer Ara, Lahara, and Trinsic trim lines. The MultiChoice 14 and 17 series is the one worth knowing. The rough-in body is universal across many trims, but the cartridge, the trim plate diameter, and the handle adapter change by series. A 17-series trim will not seat on a 14-series cartridge without the right adapter, and we’ve seen that mismatch cause a slow leak inside the wall that the homeowner only noticed as a soft spot in the drywall. To identify yours, pull the trim plate and read the stamped model number on the valve body, then measure the center-to-center spread on the handle. OEM Delta cartridges cost more than aftermarket equivalents, and aftermarket cartridges vary wildly in rubber compound and brass tolerance. For a valve buried behind tile, we recommend the OEM part; the labor to get back to it is the expensive half of the job, so the cheaper cartridge is a false savings. Our technicians have up to 19 years of experience matching trim to body across these series.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Delta Bathroom Remodeling Is Failing
- Water won’t hold temperature. The pressure-balance spool inside the cartridge has worn flat, so cold or hot spikes pass straight through. Delta 17-series valves use a rotating spool that fails gradually, which is why owners notice the shower going lukewarm before it fails outright.
- Drip from the spout with the handle off. That’s a worn seat-and-spring or a scored cartridge, and in Homestead’s hard municipal water the mineral load accelerates scoring. Left alone, it stains the tub finish and adds to the water bill.
- Handle feels loose or grinds when turned. The cartridge stem or the handle adapter is stripped. This is often a sign the trim was replaced without matching the body, a mismatch we see on plenty of 1990s Florida builds.
- Water pooling behind the trim plate or caulk pulling away. The valve body seal has failed. In Homestead, the humidity load on a shower wall is relentless, and any moisture behind the plate becomes mold within a season.
- Rough or chipped surface on the trim. Chrome, brushed nickel, and Champagne Bronze finishes pit differently. Once the plating fails, the finish is a cosmetic and corrosion problem, not a working one, but it signals the fixture is at end of life.
Replacement Cost & What’s Included

Here’s the honest installed price picture for Homestead, with parts and labor together:
- Full bathroom remodel (Delta fixtures included): $9,000 – $28,000
- Small bathroom remodel: $5,000 – $12,000
- Walk-in shower installation: $4,500 – $12,000
- Tub-to-shower conversion: $3,500 – $10,000
- Shower replacement: $3,000 – $8,500
- Vanity installation: $800 – $3,000
What moves the number: whether the valve is accessible through an existing access panel or requires opening the wall, the tile and membrane scope, and the trim finish you choose. Under Clause 1 of the Haven Standard, the price is written before anyone starts, and no change proceeds without a signed change order, so the number you agree to is the number you pay. The 365-Day Done Right Promise covers the work, and every visit includes a documented photo record of what we found and what we did.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely shut off the water at the fixture stops and inspect for a loose trim plate, corrosion, or a stripped set screw. What you shouldn’t do is open a valve body behind tile or force a seized cartridge on your own. A bathroom valve sits behind the finish wall, and the cartridge can be tight enough to crack the body if you don’t brace it correctly, which turns a $200 part into a wall repair. The other trap is a plastic P-trap or supply line that’s gone brittle with Florida heat; prying near it snaps it. If you’ve got a dripping Delta valve or you’re planning the remodel around it, call (844) 834-4248. Estimates are free, and we’ll tell you whether the part is the whole problem or whether the surrounding tile and membrane need attention too.
FAQs

How long does a Delta cartridge last? A genuine Delta cartridge typically lasts 8 to 12 years in normal use, but Homestead’s hard water and year-round humidity tend to push that toward the shorter end. If yours is original to a 2000s build, it’s due.
Can the part be repaired instead of replaced? Sometimes. A seat-and-spring kit fixes a drip on older two-handle valves, and a spool replacement handles a pressure-balance issue. If the body itself is scored or cracked, replacement is the only honest option. Call (844) 834-4248 and we’ll price both paths.
How long does the swap take? A cartridge or trim swap is typically a couple of hours once the right part is in hand. If the valve needs to come out through tile, budget a full day including patching. We’ll give you the written scope and the timeline up front.
How do you source the part? We match your stamped model number and trim series against Delta’s spec, then quote OEM. We don’t carry stock, but we can order the exact part for your body, and we’ll show you the spec sheet before we install it. The same sourcing discipline applies across our other brands, including KraftMaid, Cambria, and Silestone.
Rowan Construction Group Homestead is an independent service provider and is not affiliated with Delta.
Get Your Delta Bathroom Project Priced
Give us a call at (844) 834-4248 for a free estimate. We’ll come out, read the valve, match the part, and hand you a written flat price with the scope and the warranty before anyone picks up a tool. If you have a competitor’s written estimate, we’ll review it line by line at no charge under our Free Second Opinion offer.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












