







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Homestead Owner’s Guide
We install Schluter roof edge and drainage assemblies for Homestead homeowners, and the all-in price for a typical residential installation lands between $8,000 and $20,000 for a full roof system, with targeted repairs running $400 to $1,800 when only a section has failed. Schluter doesn’t make shingles or tiles; what it makes are the details around the perimeter – edge trim, drip profiles, and the underlayment and drainage layers that sit beneath the finished surface. Those details are what fail first in South Florida sun and rain, and they’re what this page covers.
Most Homestead owners find us after a ceiling stain appears during a summer squall, or a roofer inspecting an unrelated repair points to curled edge profile and wet underlayment at the fascia. By then the trim has usually been weathering for a few seasons without anyone noticing. If that matches what you’re seeing, the sections below walk through identifying your exact Schluter profile, understanding what the installed replacement costs here, and deciding what’s safe to check yourself versus what needs a licensed roofer. Rowan Construction Group Homestead is an independent service provider and is not affiliated with Schluter.
Which Schluter Models This Applies To

Schluter’s roof line centers on their edge and drainage profiles, and the part number matters more than most owners realize. The common profiles you’ll find on Homestead homes are the drip-and-edge types sized by the thickness of your roof buildup – a profile stamped for 1/2-inch buildup won’t seat correctly on a roof built with 5/8-inch sheathing and a thicker underlayment. If the fit is wrong, the channel won’t channel anything, and the drip edge becomes decorative.
To identify your part: look along the fascia line for a stamped profile code (the metal extrusions are stamped near the butt of each length), measure the roof buildup thickness at the eave with a tape, and note whether you have a sloped eave or a rake transition. Schluter publishes a profile reference chart that matches these numbers to a part number, and that chart – not a photo – is what we work from.
On OEM versus aftermarket: for Schluter specifically, we quote the genuine profile when the original is a Schluter assembly, because the channel geometry is what interfaces with their drainage layers. A generic drip edge from a big-box store can seal a roof, but it will not match a Schluter integrated system, so mixing the two tends to create the very gap you’re trying to fix. When a full Schluter retrofit isn’t worth it, we’ll tell you – sometimes a conventional edge assembly is the honest call.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Roofing Is Failing
- Curled or lifted edge profile. The metal extrudes over time from heat cycling; once it lifts, it stops shedding water and rain wicks behind the fascia. In Homestead this shows up fastest on the west-facing eaves that bake all afternoon.
- Staining below the eave or inside the attic. A dark line at the top of the fascia, or moisture on the underside of roof sheathing, usually means the drainage layer under the profile has been letting water through.
- Wet or crumbling dormer and chimney transitions. These are where Schluter trim and flashing meet, and where small gaps turn into rot in Florida’s monsoon season.
- UV breakdown on any exposed membrane or underlayment. South Florida’s UV index is among the highest in the country, and exposed synthetic underlayment degrades to a brittle sheet in two to four seasons if it isn’t covered.
- Visible gap between the drip edge and the gutter. If the profile’s drip lip doesn’t overhang the gutter mouth, water sheets down the fascia instead of into the trough, and the wood behind it stays wet.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the numbers look like in Homestead, with parts and labor together:
- Targeted repair of one edge run or transition: $400 to $1,800, depending on access and whether sheathing is sound underneath.
- Full roof replacement with Schluter-compatible edge assembly: $8,000 to $20,000 for a typical home.
- Tile roof sections where the profile has to be reset: $600 to $2,500.
- Metal roof installation if your assembly dictates it: $15,000 to $40,000.
What drives the range: roof pitch and eave height, the linear feet of edge treatment, whether the sheathing underneath is dry or has soft sections that need replacing, and whether the job is one local repair or a full replacement. Every Rowan quote is a flat written price with a written scope before any work starts – the numbers above are what we actually quote, not teasers. No work proceeds on a change until a change order is signed. The 365-Day Done Right Promise backs every installation, and you get a documented photo record of what we found and what we did.
DIY or Call Us?
You can safely check a few things yourself: eyeball the eave line from the ground for lifted or curled profile, note any staining on the fascia, and look at whether the drip lip reaches into your gutter. What you should not do is climb onto a wet or pitched roof in Homestead’s afternoon weather, or pry at a profile to “see what’s under it.” The underlayment and sheathing underneath tell the real story, and opening those up without replacing the edge immediately makes the water intrusion worse. Roof work at height is the part where homeowners get hurt, and beyond the fall risk, an improperly reseated edge is a leak waiting for the next storm.
The honest split: check and photograph from the ground, then call us for the part that involves the roof surface. Our technicians have up to 19 years of experience on Florida roofs, and estimates are free. Call (844) 834-4248 to schedule yours – a live person answers around the clock.
FAQs

How long does a Schluter roof edge assembly last in Homestead?
A properly installed Schluter edge assembly with intact underlayment underneath typically lasts as long as the roof surface above it – often 15 to 25 years – but the trim itself can weather faster on west-facing eaves. Homestead’s UV load is the main shortener, so inspect the eave line each spring.
Can the failed part be repaired instead of replaced?
Sometimes yes. A single failed edge run or transition can often be repaired for $400 to $1,800 rather than replaced, as long as the sheathing underneath is dry. If the profile has failed in more than one location or the underlayment is wet across the roof, a wider replacement is usually the better money.
How long does the swap take?
A targeted edge repair is typically a half-day to a full day. A full roof replacement with a Schluter-compatible assembly runs several days to a week or more depending on roof size and weather. Either way, the written scope tells you what to expect before the crew arrives.
How do you source the right Schluter part?
We match your stamped profile code and measured roof buildup to Schluter’s published reference chart, then order the genuine profile. We also source from KraftMaid, Cambria and Silestone for interior trades on the same project if needed. We don’t keep parts on a truck or claim to stock Schluter locally; the sourcing happens per job. Call (844) 834-4248 for a free estimate.
Whether you’re looking at a lifted edge profile or a full roof replacement, the next step is a written number. Call Rowan Construction Group Homestead at (844) 834-4248 to schedule your free estimate – we’ll bring the written scope, the photo record, and the 365-Day Done Right Promise, and you’ll know exactly what the job costs before anyone lifts a tool.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












