







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Homestead Owner’s Guide
Fence installation runs $3500 – $9000 installed in Homestead for a typical residential CGI-compatible run, and the number that matters is the written one, delivered before a single post is set. This page is a fence-installation guide, so it covers what a new CGI-style fence involves: panels, posts, footings, gates, and the permits that come with them in Miami-Dade County. If you are reading this because an existing fence has started to lean, sag, or rust through at the posts, the symptom picture usually starts the same way in Homestead: a gate that drags on the driveway. Then a post that moves in the wind. Then a panel that never quite straightens out.
Rowan Construction Group Homestead is an independent construction contractor and is not affiliated with CGI. We install CGI-compatible fence systems and other brands including KraftMaid, Cambria, and Silestone on the interior side of the house. Under Clause 1 of The Haven Standard, the price is written before anyone starts.
Key Takeaways
Which CGI Models This Applies To

CGI fence systems are built around a few core families: ornamental aluminum runs, vinyl and composite privacy panels, and mixed-material fence combining metal posts with composite boards. Your model line and series code sit on the hardware itself in most cases. Look on the inside of the post cap for a stamped part or series number, on the panel bracket where it meets the post, and on the gate hinge for a size designation. Measure the panel width and the post height before you call anyone. A 6-foot panel system and an 8-foot panel system use different posts, different brackets, and different gate hardware, and the size is what tells us which CGI-compatible parts you actually need.
For CGI specifically, the OEM-versus-aftermarket decision comes down to footings and finish. OEM posts are cut to the CGI system’s hole spacing; aftermarket posts often aren’t. On a Homestead property, the finish matters more than the brand stamp: salt air eats through low-grade galvanized coatings fast, and an aftermarket post with the wrong coating fails long before the OEM one would. We install CGI-compatible systems using parts matched to your existing line where that’s the right call, and replace a whole run where retrofit is the more honest choice. If your existing fence is a different manufacturer, we’ll say so on the written quote rather than assume.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Posts leaning after a wet season. Homestead’s limestone soil and summer rain saturate the ground around footings; if the original footing wasn’t deep enough, the post moves. A post that leans a quarter-inch after a rainy week is usually the start of a deeper footing problem.
- Rust streaks on the aluminum. Salt air from the Miami-Dade coast corrodes lower-grade coatings, and the streaks start at the welds and cut edges. That’s a coating failure, not a cosmetic issue.
- Gate drags on the driveway. Either the hinge has worn through or the gate post has shifted. Hinge wear is a hardware swap. Post shift means the footing is gone.
- Panels sagging between posts. A loose bracket or a post that’s tilted out of plumb. Ignore it long enough and the panel weight pulls the bracket out of the post entirely.
- White rust on galvanized parts. That’s zinc oxidation from humid air and standing water at the base. It means the coating has already been compromised.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Fence installation in Homestead runs $3500 – $9000 for a typical residential run, installed. What moves the number is length, panel height, gate count, footing depth, and the condition of the ground. A property with hard limestone near the surface can add footing time. Every quote is a flat written price with a written scope, delivered before work starts, in writing.
The quote breaks out panels, posts, footings, hardware, and labor as separate line items. Installation work is backed by the 365-Day Done Right Promise: if it isn’t done right, Rowan makes it right. Every visit includes a documented photo record as a standard deliverable. The photo record is part of the job, not an upgrade. If you have a competitor’s written estimate, bring it in and we’ll review it line by line at no charge under the Free Second Opinion offer.
DIY or Call Us?
A homeowner can safely check a few things: walk the fence and note which posts move, measure panel and post heights, photograph the series code inside a post cap, and check whether the gate hinge is loose. Those checks cost nothing and they make the written quote more accurate.
Where DIY goes wrong in Homestead is footings and wind load. A fence in Miami-Dade County sits under specific wind-load and permit requirements, and a post set in shallow concrete without a permit can fail inspection or fail the first hurricane. Fence installation done without the proper footing depth and the proper coating specification is a wasted weekend. Call (844) 834-4248 to schedule your free estimate, and we’ll put the price in writing before any work starts.
FAQs

A properly installed aluminum or composite fence with correct footing depth and a marine-grade coating typically lasts 15 to 25 years in South Florida conditions, while uncoated or lower-grade systems often fail in 5 to 10 years due to salt-air corrosion and root-level moisture. Footing depth and coating quality matter more than the brand label. Call (844) 834-4248 for an exact quote on your property.
Sometimes yes. A single leaning post, a worn gate hinge, or a loose bracket can often be repaired without replacing the run, and a repair is worth doing if the panels and remaining posts are sound. Once corrosion has reached the post base or multiple footings have shifted, replacement is usually the more economical choice. We’ll say which one applies after we inspect. Call (844) 834-4248 to book the free inspection and quote.
A typical residential fence run takes two to four days from site prep through final inspection, and the timeline depends on run length, gate count, footing conditions, and permit timing with Miami-Dade County. The written scope includes the expected duration before work starts. Permits are pulled and inspections passed before the job is closed out. Call (844) 834-4248 for your free estimate.
We source parts matched to your existing CGI line and series code, and we document the match on the written scope so you know exactly what’s being installed. If a matching OEM part is unavailable, we state the aftermarket equivalent and its spec differences on the quote before you approve anything. Nothing is ordered until the written price is signed. Call (844) 834-4248 to start the quote.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












