







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Bathroom Remodeling: The Homestead Owner’s Guide
We install American Standard-compatible bathroom fixtures and remodeling packages in Homestead, and a full bathroom remodel typically runs $9,000 – $28,000 installed, with smaller baths at $5,000 – $12,000. Fixture swaps and targeted replacements (a toilet, a vanity, a shower valve trim) sit at the low end of that band; full gut-and-rebuild work on a 1970s Homestead ranch home sits at the high end. We are an independent contractor and are not affiliated with American Standard.
Most Homestead owners don’t come to this page because they want a remodel. They come because something failed. The toilet runs for twenty seconds after every flush. The shower valve drips a thin line down the tile even when the handle is off. A towel bar pulled out of drywall and took a fist-sized plate of it with it. Or the floor around the toilet base gives underfoot, and there’s a soft dark ring on the grout line. Those are the four entry points we see on American Standard bathrooms across Homestead, and each one points to a different part, a different repair, and a different conversation about whether to patch or remodel.
Which American Standard Models This Applies To

American Standard’s residential bathroom line spans a lot of ground, and the part you need depends on which line your fixture came from. The main families we work with:
- Champion and Cadet toilets – gravity-flush units common in Homestead homes built or updated between 1995 and 2015. Flush valve, fill valve, and flapper assemblies differ between the two; a Cadet flapper will not seal correctly on a Champion bowl.
- Colony and Boulevard – older two-piece models; the tank-to-bowl gasket is the first thing to fail on these, and the parts aren’t interchangeable with modern Cadet tanks.
- Green Tea and Serin – shower and tub trim lines. The cartridge is the failure point, and the cartridge part number changes with the rough-in valve series behind the wall, not the trim.
- Studio and Town Square – vanity and sink basins; vessel and undermount models use different drain assemblies and different overflow paths.
How to identify yours: pop the tank lid and look for the model stamp on the inside of the tank wall, usually a stamped number and a two-letter code. For shower trim, remove the handle (usually a set screw underneath) and look for the valve body stamp behind the escutcheon. Take a photo of both stamps with your phone before you call anyone. On the OEM-versus-aftermarket question: American Standard OEM parts fit with zero fuss, but for high-wear pieces like flappers and fill valves, a quality aftermarket equivalent from Fluidmaster or Korky is often more durable than the OEM part and costs less. For cartridges and valve bodies, we use OEM or exact-match only, because tolerance on those parts is tighter and a knockoff cartridge will drip within a year.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Bathroom Remodeling Is Failing
These are the symptoms Homestead owners describe most often, matched to what’s actually failing underneath.
- The toilet runs or “ghost-flushes” between uses. A flapper that no longer seats flat, or a fill valve that never fully closes. Both are usually a $15 – $40 part and ten minutes of labor. Left alone, they add real money to your water bill each month.
- The shower drips when the handle is off. The cartridge inside the valve body has worn its seat. You’ll often see a mineral crust along the tile line below the handle. In Homestead’s hard water, cartridges wear faster than the manufacturer’s stated life, often by several years.
- The toilet rocks when you sit on it, or the floor is soft at the base. A failed wax ring let water past the flange over months or years. The wood subfloor under the tile has absorbed it. This one is a floor problem wearing a toilet costume, and it needs the subfloor opened.
- Caulk lines keep cracking or turning black within months. Moisture behind the tile, not a bad caulk job. Re-caulking over it just hides the problem until the grout starts to fail too.
- The vanity cabinet sags or the sink drains slowly. Particleboard cabinet boxes swell once they’ve been wet, and the P-trap or drain assembly is often clogged with hair and soap scale. An American Standard undermount basin can also have a failing overflow gasket that leaks into the cabinet, not the drain.
Replacement Cost & What’s Included

Here’s where the pricing lands in Homestead, by job type:
| Job | Installed Range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What drives the number up: whether the subfloor has to be opened and rebuilt (common in Homestead homes with slab-on-grade construction), whether the shower pan needs a new mud bed, whether the valve body has to be replaced behind the tile, and how far the tile pattern runs. What drives it down: a working rough plumbing setup, no floor rot, and keeping the existing footprint.
The written quote lists parts and labor separately, so you can see what a Champion fill valve costs versus a cartridge swap. Every visit includes a documented photo record of what we found and what we did. The work is covered by the 365-Day Done Right Promise, and the price is written before anyone picks up a tool.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. What you can safely do yourself: replace a toilet flapper, replace a fill valve, swap a vanity faucet aerator, re-caulk a tub line (after the old caulk is fully removed and the joint is dry). Those are low-stakes, no-tool-danger jobs, and if you get them wrong, the worst outcome is a drip.
Where DIY goes wrong: pulling a shower cartridge from an American Standard Green Tea valve. The cartridge is held inside a brass body with a retention clip, and muscling it out can crack the valve body or damage the tile behind the escutcheon. Replacing a valve body requires cutting the hot and cold supply lines and sweating or press-fitting new connections. That is plumbing work, and a mistake means water in a wall. Pulling a vanity that hides a slow leak is also a job for a crew, because what’s behind it is often a floor that needs repair, not a cabinet that needs swapping.
What we’d suggest: if it’s a flapper or a fill valve, and the toilet is stable and the floor is solid, replace it. If it’s a shower valve, a soft floor, or anything that touches tile, call Rowand Construction Group Homestead at (844) 834-4248. The call is free, and we’ll tell you whether you need a repair or a remodel before anyone drives out.
FAQs

Expect 15 – 25 years on a properly built shower pan and tile job, and 8 – 12 years on shower cartridges in Homestead’s hard water, which is shorter than the manufacturer’s stated life. Toilets typically run 15 – 20 years before flappers, fill valves, and tank gaskets need replacing. The fixtures are durable; the wear parts and the tile assembly behind them are what age. Call (844) 834-4248 for a free estimate on what a full rebuild would cost for your bathroom.
Usually yes, if the failure is isolated to the flapper, fill valve, cartridge, or wax ring, and the substrate behind it is sound. A cartridge swap on a Green Tea valve typically runs a few hundred dollars installed. A wax ring replacement is a few hundred more if the subfloor is intact. Once the subfloor or tile assembly is involved, repair and partial remodel converge, and that’s when a full remodel often makes more financial sense. Call (844) 834-4248 and describe what you’re seeing; we’ll quote both paths, free.
A single fixture swap (toilet, vanity, shower cartridge) takes a few hours to a day. A tub-to-shower conversion runs 1 – 2 weeks. A full bathroom remodel runs 3 – 5 weeks depending on tile, permit timing, and whether the floor has to be rebuilt. We’ll give you a written schedule with the written price, so you know both numbers before anyone starts. Call (844) 834-4248 for the free estimate.
We source American Standard parts by model number and, for shower valves, by the valve body series behind the wall, not the trim line, because that’s the mismatch we see most often. We use OEM parts for cartridges and valve bodies, and quality aftermarket equivalents (Fluidmaster, Korky) for high-wear flappers and fill valves where they’re more durable than OEM. We do not stock parts on a truck; we order from the manufacturer or an authorized supplier, and we tell you the lead time upfront in the written quote. Call (844) 834-4248 for a free estimate.
If you’re also thinking about cabinetry or counters while we’re in there, we work with KraftMaid, Cambria, and Silestone alongside American Standard on the fixture side, so the whole bath gets one written scope and one written price.
Get Your Written Price from Rowan Construction Group Homestead
Every estimate starts with a written, flat price and a written scope, delivered before any tool is picked up. No “call for a quote.” No change proceeds without a signed change order. If you have a competitor’s written estimate for a bathroom job, we’ll review it line by line at no charge as a Free Second Opinion. Our technicians have up to 19 years of experience, and every visit includes a documented photo record as a standard deliverable.
Call (844) 834-4248 for a free estimate on your American Standard bathroom project in Homestead. Tell us what your toilet, shower valve, or vanity is doing, and we’ll tell you what it’ll take to fix it and what it’ll cost.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












