







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Home Additions & ADU: The Homestead Owner’s Guide
We install and repair Barrette-branded home additions and ADU systems for Homestead homeowners, with typical installed pricing running from $45,000 to $130,000 for a home addition and $90,000 to $220,000 for a full ADU. Barrette’s outdoor living lines are original equipment on thousands of South Florida additions, and when a component like a screen enclosure track, framing channel, or roof panel connector starts to move, the fix is usually specific to the Barrette profile. A Barrette-manufactured addition that’s cracking at the post base or letting water past the roof panel seam is the most common call we get in Homestead, and behind it is almost always a failed connector or a fastener that lost its grip after one too many hurricane-season flexes.
Key Takeaways
- Installed Barrette-compatible addition work in Homestead: $45,000 to $130,000 depending on span and structure.
- ADU construction: $90,000 to $220,000, driven mostly by foundation scope and electrical service.
- The Barrette profile matters – a generic replacement connector won’t match the original extrusion.
- We source the correct part and quote the flat installed price in writing before any work starts.
- Homestead wind code adds cost to every addition; we pull the permits and pass the inspections.
Which Barrette Models This Applies To

Barrette’s structural aluminum and screen-enclosure framing shows up across its outdoor living catalog, and the profile geometry has changed several times over the years. The same nominal post size can carry a different wall thickness and a different channel dimension depending on when the section was extruded. That means if you’re ordering a replacement framing member or connector, a part that fits the outside dimensions can still be wrong on the inside.
The way to get it right is to find the stamped or adhesive ID label inside the addition: it will name the series and, if you can read it, the extruded profile run. If the label is gone, we take two measurements that matter more than the nominal size – the channel opening and the web thickness – and cross-reference them before ordering. On Barrette specifically, the OEM-versus-aftermarket decision usually favors OEM for structural connectors and the profile-specific pieces, because the extrusion shape is the whole match. For non-structural items like snap covers and vinyl trim, a quality equivalent is fine and often faster to source. We’re an independent service provider and not affiliated with Barrette; what we bring is the measurement and the record that the correct part left and the right part went on.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Home Additions & ADU Is Failing
- Water staining on the roof panels. When a panel seam lets go, the first sign is a dull brown streak on the panel underside. That’s usually a failed seam cap or a fastener that backed out of the purlin, not a roof that’s worn out.
- Creaking or flex in the framing. A post or beam that moves underfoot means a connector has lost tension. In Homestead, the daily thermal swing plus the wet season is enough to loosen a set screw that was never torque-checked.
- Cracks radiating from a post base. Corner and post footings are where the load concentrates. A hairline crack is often the concrete footing and the connector interface separating, and the fix is a footing review, not just a new connector.
- Door and window tracks that bind. If a screen door drags on its track, the frame may have racked. That’s a structural symptom in a Barrette screen or enclosure, and it gets worse in wind.
- Discolored or brittle plastic connectors and seals. UV in South Florida eats polymer parts faster than most of the country. Two to four years is a realistic service life for sun-exposed connectors, so a part that’s graying and hard is a part that’s close to failing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Homestead, a Barrette addition repair typically runs $45,000 to $130,000 installed when the scope is a home addition, and $90,000 to $220,000 for a full ADU, though a targeted repair to a component – reseating framing, replacing connectors, re-capping roof panels – is a fraction of that and often starts near $1,500 to $9,000. The range is driven mostly by the span of the addition, the footing scope, and whether the work touches the electrical service. Every quote is a flat written price with a written scope, so the number you sign is the number you pay; no change proceeds until the change order is signed. The work carries the 365-Day Done Right Promise, and every visit includes a documented photo record. Call (844) 834-4248 for an exact quote.
DIY or Call Us?
You can safely identify and check the part yourself. Take photos of the ID label, measure the channel opening and web thickness, and note where water is staining or a connection has moved. Where DIY goes wrong on a Barrette addition is at the connection points – a framing member that’s cut to fit and bolted back wrong can crack the footing, and a screen panel that’s re-fastened without the right tension will fail in the first strong wind of hurricane season. We recommend a trained professional for anything that carries structural load or touches the roof panels. What you can do first is call (844) 834-4248 for a free estimate. We’ll review the photos and the measurements and give you a written flat price, no change orders without your signature, and a technician who’s been background-checked before they arrive.
FAQs

Structural aluminum framing in a Barrette addition typically lasts 15 to 25 years in Florida, but the exposed connectors, seals and fasteners will need replacement every two to four years because of UV and the wet season. When one part fails, we check the rest of the same profile for the same wear.
Sometimes. A connector that’s merely loose can be re-tensioned, and a seam cap can be reset. A framing member that’s cracked, or a footing that’s separated, has to be replaced, and we’ll tell you which you’re looking at before we quote the repair. Call (844) 834-4248 and we’ll review the condition and the repair-versus-replace call with you.
A single connector or seam cap is usually a half-day visit. Full framing or panel replacement on a Barrette addition runs two to four days, depending on the span. Homestead wind-code inspections add time, and we pull those permits and schedule the inspection as part of the job.
We take the ID label plus the channel-opening and web-thickness measurements, verify the profile against Barrette’s current and legacy parts, and then order from the vetted material line, just as we do with KraftMaid, Cambria, and Silestone for our other trades. We don’t claim to stock parts; we source the right one for your model and record what went in. Call (844) 834-4248 to start with a free estimate.
The number is on the page before anyone picks up a tool, and the part on your Barrette addition gets matched to the model, not guessed. For a free estimate on your Homestead home addition or ADU repair, call (844) 834-4248. A live person answers, and we will review photos, measurements, and the written scope with you before scheduling.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












