







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mighty Buildings Bathroom Remodeling: The Homestead Owner’s Guide
We install Mighty Buildings-compatible bathroom remodeling in Homestead for a typical installed price of $9,000 – $28,000 on a full room and $5,000 – $12,000 on a compact bathroom, with a written flat price before any work begins. If you’re wondering whether we treat a prefab panel shell differently than a block-and-stucco house: we do, and that’s the entire point of this page. In a Mighty Buildings home, you don’t discover a bathroom failure through a rusted drain the way you would in a 1970s ranch. You discover it when the floor feels just slightly soft under the bath mat, or when the shower pan holds a half-inch of water after every use and the trickle disappears overnight.
Key Takeaways
- Mighty Buildings bathroom systems are factory-designed assemblies – replacements need parts that match the panel series, not generic stock.
- The most common Homestead failure is moisture migrating under a factory-set shower pan because our summer rain and humidity push the room’s dew point into the wall cavity.
- Every Rowan job comes with a written flat price before work starts, the 365-Day Done Right Promise, and a documented photo record on every visit.
Which Mighty Buildings Models This Applies To

Mighty Buildings built homes primarily in the Western US before expanding, and the bathroom assemblies vary by build year and panel system. If you own one of these homes in Homestead, the first thing to do is find the model and build tag – usually a printed label inside a vanity cabinet, on the inside face of the water heater closet, or laser-etched on the underside of the floor panel at the door threshold. Photograph it before you call anyone. The tag will list the panel series and often the factory plumbing rough-in spec. That spec determines whether you can drop in a standard 60-inch tub, whether the shower drain sits center, left, or offset, and whether the wall cavity is deep enough for a full-depth valve body.
On the OEM-versus-aftermarket question: for Mighty Buildings specifically, we don’t chase original factory parts because the factory-specific components (custom pan foam, pre-cut cement board panels) were produced in finite runs. Instead we use matched equivalents – a Schluter Kerdi shower pan sized to the rough opening, a standard 2-inch shower drain with the correct PCI seal, fiberglass-mat cement board cut to panel dimensions. Same performance, available today, warranty-backed. We also work on bathroom fixtures from KraftMaid, Cambria, and Silestone when those were installed in a previous refresh. To be clear about one thing: Rowan Construction Group Homestead is an independent service provider. We’re not affiliated with Mighty Buildings and we don’t stock their parts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mighty Buildings Bathroom Remodeling Is Failing
These are the patterns we’ve seen repeatedly on Mighty Buildings bathroom calls across Homestead. Each one has a specific cause, and knowing which one you have changes what the repair actually involves.
- Soft spots in the bathroom floor near the shower or toilet. The panel subfloor is engineered, not plywood – usually a cementitious factory finish over a structural core. When it feels spongy, water has been getting under the finished floor for weeks. The cause is almost always a failed perimeter caulk joint where the floor meets the shower curb or wall panel.
- Shower pan that holds water 12+ hours. Pre-sloped factory pans rely on a precise drain connection. A slight settle or a failed drain gasket lets water sit rather than head to the drain. In Homestead this happens more here than in dryer climates because slab heave from evening thunderstorms warps the pan geometry.
- Bubbling or lifting paint on the ceiling below the bathroom. Water is escaping from above, usually from a failing seal at the shower valve escutcheon or a vertical joint behind the tile. The eight inches of ceiling crack you see is roughly the last 10 days of a problem that’s been active for months. Check HOA zones in Homestead before assuming the ceiling drywall is yours to fix – many subdivisions assign that to the association.
- Grout powdering or falling out along the shower base. The tile adhesive was applied over a cement board that has absorbed moisture, and the grout is now flexing with the substrate. Not a cosmetic issue – that powder is a signal the tile is coming loose.
- Musty smell that returns within a week of cleaning. Active mold growth in the wall cavity behind the shower. The cause is either a failed backer-board seam or an exhaust fan that’s undersized for the square footage. In Homestead’s humidity, an 80 CFM fan on a 40-square-foot bathroom doesn’t move enough air. Most factory installs shipped with 50 – 70 CFM units.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed price in Homestead for Mighty Buildings-compatible bathroom work runs $9,000 – $28,000 for a full bathroom remodel, $5,000 – $12,000 for a compact bathroom, and $4,500 – $12,000 for a walk-in shower installation. A tub-to-shower conversion is typically $3,500 – $10,000, a shower replacement on its own $3,000 – $8,500, and a bathroom vanity installation $800 – $3,000.
What drives the price up: whether the pan foam or tile membrane has to be removed (membrane failures cost more than surface leaks), whether the drain has to be re-positioned to match standard 60-inch tub alignment, and whether the exhaust fan needs upgrades to meet Homestead’s Florida Building Code ventilation rate. What drives it down: keeping the existing layout and door position, standard 60-inch tub sizing, and using a straight-set tile in place of a complex pattern.
Every quote we deliver is a flat written price with a written scope and a written warranty. No “call for a quote.” No change proceeds until a signed change order is on file – that’s the discipline that’s kept our projects within a few percent of the agreed price across 4,000-plus jobs since 2007. The 365-Day Done Right Promise covers the install for a full year: if it’s not done right, we make it right. We’ll also give you a free second opinion on any written estimate from another contractor – bring the quote, we’ll read it line by line at no charge.
DIY or Call Us?
What an owner can safely check: whether the bathroom floor is soft (step on every square foot, listen for movement), whether the shower pan holds water overnight, whether the exhaust fan runs at all, and whether the ceiling below shows staining. Photograph what you find. Those four checks alone narrow the cause to two or three possibilities before we arrive.
Where DIY goes wrong here is not the tile. It’s the drain connection and the pan membrane. The pan is a single mechanical assembly designed to sit under the tile with a specific slope and a specific drain gasket seal. Over-tighten that gasket and it cracks; under-tighten it and you get a slow leak into the ceiling below – over the course of weeks, in a Homestead thunderstorm season, that slow leak becomes a framing repair. We’ve also seen owners cut into the factory panel subfloor thinking it was standard cement board and discover it wasn’t; the repair to that misjudgment was more expensive than the shower job that started it. Fixture swaps (vanity, faucet, mirror) are fair game for a confident DIYer. Pan and drain work, call us.
Call (844) 834-4248 for a free estimate – a live person answers around the clock, and a background-checked, uniformed technician will arrive with a photo record of what was found and what was done. Our technicians have up to 19 years of experience.
FAQs

Most factory panels themselves are sound for 20+ years; the failure items are the seals, the pan membrane, and the exhaust fan. Expect to replace the pan membrane and re-seal perimeter joints at roughly year 8 – 12 in Homestead’s humidity, then again at a similar interval. Call (844) 834-4248 for a free estimate if yours is showing the symptoms above.
Yes, in most cases. A failed perimeter seal or a loose tile is a targeted repair – usually $1,500 – $4,000 depending on how far the moisture has spread. A failed pan membrane or a soft subfloor panel is a replacement, not a patch. We’ll tell you which one you’re looking at from the photo record after the first visit. Call (844) 834-4248 for an exact quote – estimates are free.
A vanity-only swap is one day. A shower replacement is typically three to five working days. A full bathroom remodel is 10 – 15 working days, mostly ceiling tile cure time. We schedule around the fact that a Mighty Buildings bathroom is usually the household’s only shower or only tub, and the written scope notes exactly which days the bathroom is out of service. Call (844) 834-4248 to schedule a free estimate.
We don’t carry Mighty Buildings branded stock and we don’t stock parts on a truck. We identify your panel series from the factory tag, then spec matched equivalents from our vetted material list and confirm dimensions before ordering. That’s how the quote has honest numbers. Call (844) 834-4248 with your tag photo and we’ll price it.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












