







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Homestead Owner’s Guide
Schluter bathroom remodeling in Homestead costs $9,000 – $28,000 installed, and the figure that matters most inside that range is the waterproofing layer: the Schluter KERDI membrane, DITRA uncoupling mat, or KERDI-BOARD panel behind your tile. Most Homestead owners don’t discover that layer failed until a grout line near the shower curb turns dark, a tile sounds hollow under a knuckle, or a baseboard on the far side of the wall starts to swell. By then water has usually been traveling for months behind the tile, which is why we open the wall and photograph what we find before quoting the repair.
Which Schluter Models This Applies To

Schluter isn’t a single product line, and matching the right system to your bathroom means knowing which one is already on the wall or floor. The common systems in Homestead homes:
- KERDI and KERDI-BAND – the sheet-applied waterproofing membrane for shower walls and floors, sold in 5-meter and 30-meter rolls at 125mm and 200mm widths, with matching inside and outside corners.
- DITRA and DITRA-XL – the uncoupling mat under floor tile, 3mm and 5mm thick respectively. DITRA-XL adds height, which changes your transition to the hallway and to any adjacent carpet or vinyl.
- KERDI-BOARD – the foam-backed tile substrate panel, in 12.5mm and 25mm and 50mm thicknesses. The thickness is the compatibility gotcha: swapping 12.5mm board for 25mm board shifts the tile face out by half an inch and throws off your trim, door jamb, and shower valve depth.
- KERDI-LINE and KERDI-DRAIN – linear and point drains with integrated bonding flanges; the flange is what makes the drain waterproof, not the caulk around it.
- SHOWERPROFILE and DILEX – edge and movement profiles. The inside corner pieces are model-specific, so a generic hardware-store corner will not seat.
Identify what you have by reading the printed edge strip on the membrane (it repeats the product name and roll width) or the imprinted grid on DITRA. Take a photo of the label and the thickness at a cut edge. Because these are system components with tight tolerances, we install Schluter-compatible assemblies rather than mixing brands: a KERDI flange bonded to a non-Schluter drain body is the single most common failure we’re called to correct in Homestead. Rowan Construction Group is an independent contractor and is not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
- Hollow-sounding tile in the shower floor. A dull thud instead of a sharp tap usually means the thin-set has debonded from the DITRA or from the slab under it. In Homestead, that often traces to a mat installed without full coverage, then punished by our summer slab movement.
- Dark or re-emerging grout lines near the curb and drain. Grout darkens when moisture sits behind it. If you’ve regrouted twice in three years and it keeps coming back, the membrane beneath is not doing its job.
- Efflorescence or a chalky white bloom on the shower wall. Water is wicking through and evaporating, leaving mineral salts. That means the KERDI seam or corner was never properly overlapped and banded.
- Loose tile at the wall-to-floor joint. Movement at that joint is normal; a failed movement joint (missing DILEX, or grout packed where sealant belongs) transfers that movement into the tile and pops it.
- Soft drywall or a swollen baseboard on the room’s back side. This is the quiet one. Water has left the shower, crossed the framing, and is now damaging a wall in the next room, which is why we open and photograph rather than guess.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Rebuilding a shower or tub surround with Schluter-compatible waterproofing and new tile runs $4,500 – $12,000 for a walk-in shower, $3,500 – $10,000 for a tub-to-shower conversion, and $9,000 – $28,000 for a full bathroom remodel in Homestead. A shower-only membrane and tile rebuild with no layout change lands at the low end; the range climbs with linear drains, KERDI-BOARD substrate replacement, larger-format tile, and glass.
What moves the number: how much framing has to come out, whether the drain is salvaged or replaced, tile selection, and whether the subfloor needs flattening. You get one flat written price with a written scope and a written warranty before any tool is picked up. If the wall opens and we find rot the original quote couldn’t see, nothing changes until you sign a change order. Every visit includes a documented photo record. The 365-Day Done Right Promise covers the work: if it isn’t done right, we make it right.
DIY or Call Us?
Membrane work looks like peel-and-stick vinyl, and that’s where homeowners get into trouble. A KERDI seam that isn’t overlapped the required amount, a corner band applied over dust, or thin-set mixed too dry will pass a visual check and fail within two summers. This isn’t electrical or a tensioned spring, so it won’t hurt you, but it will quietly rot your subfloor while the tile still looks fine.
You can safely check: tap tiles for hollow spots, look at the grout at the curb and drain, photograph the product label at a cut edge, and note whether the shower pan holds water without draining down at the perimeter. What you shouldn’t do is re-tile over an existing waterproofing layer you can’t verify. Call (844) 834-4248 and we’ll tell you honestly whether a repair or a rebuild is the right call.
FAQs

A properly installed KERDI or DITRA assembly should last the life of the tile – decades – but in South Florida’s humidity and with our slab movement, an under-covered mat can start to show problems in 5 to 8 years. Lifespan is set by installation quality, not the product. Call (844) 834-4248 for a free estimate and we’ll inspect what you have.
Sometimes, but only if the failure is localized and the surrounding membrane still bonds. A single failed drain flange or a bad corner band can often be cut out and re-banded. If the hollow spots are widespread, a spot repair just moves the problem 18 inches over. The honest answer usually comes from opening the wall and looking.
A shower or tub surround rebuild typically runs 4 to 7 working days, with demo, substrate repair, membrane, cure time, tile, and grout. Cure time for the thin-set and membrane is real and shouldn’t be rushed – it’s why we schedule it, not skip it. A full bathroom remodel takes longer, and we give you the schedule in writing up front.
We source through Schluter’s distribution chain and match the specific series, roll width, and thickness to your existing work. We don’t claim to carry parts on a truck. If a discontinued profile or an older KERDI-BOARD thickness is what your bathroom has, we say so and quote the correct replacement rather than substituting a size that won’t line up. We also work with KraftMaid, Cambria, and Silestone when the project includes cabinets or counters.
Call (844) 834-4248 to schedule your free estimate. Bring a competitor’s written quote and we’ll review it line by line at no charge.
Written by the team at Rowan Construction Group Homestead, serving Homestead and nearby areas.












